|
Bogen
3021, 3221/ 055 Tripod Parts
This
style was any 3021/3221/3021S/3221S/
055/ 055SH/ 055B made before 1999
3021/055 is silver, 3221/055B is the
same tripod only black. All
parts supplied are for the silver
tripods. |
 |
A
USED Upper leg lock for 3021 Old
style.
A1 Upper leg lock clamp
new style for 3021 Old style.
B USED Lower leg lock
for the 3021 Old style tripod.
B1
Lower leg lock clamp new style
for the 3021 Old style tripod.
C
Rubber foot
D
Grub screws
E
USED Main Casting
*
USED Center Column
F
Center column Lock Knob
H1
USED Upper Leg Tube With Leg Brace
H2
USED Middle Leg Tube
H3 USED Lower Leg Tube
with foot
I
Replacement Flip lever for the
old style "flip Lock" only.
Will not fit
the newer 3021N/PRO style leg locks.
J
Nut caps
|
The newest version of
the 3021PRO leg locks:
  Snap
locks that flip in and out instead
of rotate up and down, shown at
left. Old style is shown at
the right.
|
A
USED Upper leg lock clamp for
3021 Old style. This
part has been formally discontinued
by Bogen. We occasionally get a few
used parts from time to to time.
These are not always available.
Condition is good, some scratches
and wear marks but completely usable
and complete working parts.
A1
NEW Upper leg lock clamp for
3021 NEW style. Newer style
snap lock action. These are
always available since they fit the
newer tripods.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
|
B
USED Lower leg lock clamp for
the 3021 Old style tripod.
This
part has been formally discontinued
by Bogen. We occasionally get a few
used parts from time to to time.
These are not always available.
Condition is good, some scratches
and wear marks but completely usable
and complete working parts.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
B1
NEW Lower leg lock clamp for
3021 NEW style. Newer style
snap lock action. These are
always available since they fit the
newer tripods.
|
 |
C
200SPK3 Spiked
Feet Set $34.99
|
 |
C
Rubber foot set of three
press fit at the bottom of each leg
and keep the aluminum tube from
scratching your floors.
|
 |
D
Grub screws (shown left) are
the three screws that keep the head
tightly locked on the tripod column.
Sold individually.
|
 |
E
USED Main Casting (shown
left). This
is the one thing that holds the 3021
together. The legs hinge from
this casting, and the center column
rides in the middle.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
|
 |
E1
USED Center Column
All used parts are
subject to availability: Since these
parts are not readily available and
orders that cannot be filled will be
cancelled and refunded
|
 Old
locking lever that is no longer
available
New style
locking key and pin for the
replacements
  |
F
Center column Lock Knob
No longer
Available for Bogen 3021/3221
(old style) tripods (shown left).
This
part has been formally discontinued
by Bogen. It is not available.
Modification parts are available,
but the main casting and the top
plate must be modified requiring the
enlarging the opening of the cast
aluminum casting .
Click here to
go to that page.
The locking Key
R055,106 is available. The knob and
spring are not.
|
 |
G
Leg Brace (shown
left). No
longer Available by itself, and only
available used with the top leg tube
attached. This is the
part that holds the leg to the main
casting and allows the leg to move
in and out to the side. The
brace (part G in picture above) has
one bolt and is the direct
replacement for the old style 2 bolt
leg brace. The locking pin and
spring will fit either brace with no
modification or changes needed.
Part A
in the photo to the left may be the
oldest available. the size and
width of the pins is the same as
B and
C.
Part B
is the newest part, using one screw
on the back instead of two like on
part C.
Part C
is the most common part available.
|
|
H1 USED Upper Leg with Leg
Brace (shown left and above).
This is USED and is not always
available.
Condition is good, some scratches
and wear marks but completely usable
and complete working parts.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
|
| |
H2
USED Middle Leg Tube
(shown left).
This is USED and is not always
available.
Condition is good, some scratches
and wear marks but completely usable
and complete working parts.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
|
| |
H3
USED Lower Leg Tube (shown
left). This is
USED and is not always available.
Condition is good, some scratches
and wear marks but completely usable
and complete working parts.
All used parts are subject to
availability: Since these parts are
not readily available and orders
that cannot be filled will be
cancelled and refunded
|
 |
I
Replacement Flip lever for
the old style double spiral "flip
Lock" as shown at right. Fits
the OLD STYLE double spiral "flip
Lock" only.
Will not fit the newer 3021N/PRO
style snap lock leg locks, or some
of the oldest single spiral leg locks.
There is no way to tell which leg
lock uses this lever so if in doubt
it is better to buy a whole clamp
assembly.
|
 |
J Nut
caps (shown left) help to lock
the tension nuts on the leg locks,
so as to keep the tension even
during years of use and to keep the
nuts from working loose and getting
lost. Packs of 5.
Will not fit
the newer 3021N/PRO style leg locks. |
